Keyence DV-90 User Manual

AutoID Data ControllerDV-90User’s ManualRead this manual before using the system in order to achieve maximum performance.Keep this manual in a safe pl

8E DV-90-IM9-5 Settings...

5-2E DV-90-IM5Extended Functions5-1 Reference Data Function Use the reference data function to display a character string instead of raw code data.Ref

5-35E DV-90-IMExtended Functions5-1 Reference Data FunctionUsing the Reference Data FunctionThe following settings are required for using the referen

5-4E DV-90-IM5Extended Functions5-2 Input Digit Limitation FunctionThe input limitation function is used to verify the master data and the extracted p

5-55E DV-90-IMExtended FunctionsSetting the Input Limitation FunctionThe settings for the input limitation function are as follows:• Direction of the

5-6E DV-90-IM5Extended Functions Setting the Input Digit Limitation Function1 Move to the setting mode.Press the key for one second. The displayente

5-7E DV-90-IM5Extended Functions5-3 Port Number Limitation FunctionThe port number limitation function makes it possible to add the information on whi

5-8E DV-90-IM5Extended FunctionsDescription of Port Number Limitation FunctionThis section refers to the table shown below.• Data consisting of “11111

5-9E DV-90-IM5Extended FunctionsVerify Limitation FunctionThe read data can be verified with multiple parts of the bar code data at one verification p

5-10E DV-90-IM5Extended Functions5-4 Verify Limitation FunctionDate Compare FunctionWhen the date information is included in the bar code, it can be

5-115E DV-90-IMExtended Functions• When “DEF12041215XYZ456” is read (Current date is December 1, 2004.)Setting the Verify Limitation FunctionThe follo

9E DV-90-IMManual StructureDescribes the features, functions, part names, system configuration, and the con-nectable devices of the DV-90.Describes th

5-12E DV-90-IM5Extended Functions5-4 Verify Limitation Function Checking the commodity code and expiration date of an GS1-128 code using a differ-en

5-135E DV-90-IMExtended Functions5-4 Verify Limitation FunctionPerformance of 3-Point-A Verification and 3-Point-B VerificationThe Verify Limit in 3-

5-14E DV-90-IM5Extended Functions5-5 Read Quality Check FunctionThe read quality check function checks the reading stability of the connected code rea

5-155E DV-90-IMExtended Functions5-5 Read Quality Check FunctionSetting the “Read Quality Check Function” of the DV-901 Move to the setting mode.Pres

5-16E DV-90-IM5Extended Functions5-5 Read Quality Check FunctionInstalling the Code Reader under the Same Conditions as in the BL SeriesInstall the B

5-175E DV-90-IMExtended Functions5-5 Read Quality Check Function6 Make a fine adjustment to the reading quality.Press the or key to make a fine a

5-18E DV-90-IM5Extended Functions5-6 Data Editing in the Preset ModeThis section explains editing in the preset mode. Data Editing in the Preset ModeT

5-195E DV-90-IMExtended Functions3 Move to the detail screen in the preset mode.Display the detail screen by pressing the key, and switch the displa

5-20E DV-90-IM5Extended FunctionszChanging charactersChange characters by pressing the or key.zDeleting charactersDelete a character by placing th

5-215E DV-90-IMExtended Functions5-6 Data Editing in the Preset ModeSetting the Verify Limit1 Display the data detail screen.Perform Step 1, 2, and 3

MEMO10E DV-90-IM

5-22E DV-90-IM5Extended Functions5-6 Data Editing in the Preset Mode5 Exit the detail mode.Press the key.The record number indicator LEDs stop flas

5-235E DV-90-IMExtended Functions5-6 Data Editing in the Preset Mode5 Set the Limit Direction, Limit Start, and Date Compare.Display “Digit Specify”

5-24E DV-90-IM5Extended Functions5-6 Data Editing in the Preset ModeSetting the Port Number Limitation1 Display the data detail screen.Perform Steps

5-255E DV-90-IMExtended Functions5-6 Data Editing in the Preset ModeSetting the Output Number1 Display the data detail screen.Perform Steps 1, 2, and

5-26E DV-90-IMMEMO5Extended Functions

6-166E DV-90-IMSettingThis chapter describes the setting procedures for the DV-90.6-1 Setting Procedures ...

6-2E DV-90-IM6Setting6-1 Setting ProceduresThis section explains how to navigate through the DV-90 setting menus using the front panel.To Start the S

6-36E DV-90-IMSetting6-1 Setting Procedures7 To return to the previous menu, press the key.Another setting menu can be selected.Change the settings

6-4E DV-90-IM6Setting6-2 Setting Items of the DV-90This section describes the items to be set in each setting menu of the DV-90. For details on the se

6-56E DV-90-IMSetting6-2 Setting Items of the DV-90 Setting item details Setting Item LCD Display

1-111Getting StartedThis chapter describes the features and configuration of a typical DV-90 setup. 1-1 Checking the Package Contents...

6-6E DV-90-IM6Setting6-2 Setting Items of the DV-90Verification Setting Menu Menu listVerification setting menuParallel output typeOutput data typeA

6-76E DV-90-IMSetting6-2 Setting Items of the DV-90 Setting Item LCD Display Select

6-8E DV-90-IM6Setting6-2 Setting Items of the DV-90BCD outputIn this output, 12 bits are delimited into 4 bits each, and each chunk is assigned with

6-96E DV-90-IMSetting6-2 Setting Items of the DV-90 Setting item details Setting Item LCD Display

6-10E DV-90-IM6Setting6-2 Setting Items of the DV-90 Setting Item LCD Display Selec

6-116E DV-90-IMSettingI/O Settings Menu Menu listI/O settings menuInput typeParallel output ON timeParallel output delay timeREMOTE input assignmentP

6-12E DV-90-IM6Setting6-2 Setting Items of the DV-90Options Setting Menu Menu listOptions setting menuBacklightKey protect (PRESET key)Key protect (

6-136E DV-90-IMSetting6-2 Setting Items of the DV-90 Setting Item LCD Display Sele

6-14E DV-90-IMMEMO6Setting

7-177E DV-90-IMHow to Use the SetUp SoftwareThis chapter describes the installation procedure and operation method for the SetUp Software.7-1 Installa

1-2E DV-90-IM1Getting Started1-1Checking the Package ContentsThe package contains the following equipment and accessories. Before using the DV-90, che

7-2E DV-90-IM7How to Use the Setup Software7-1 Installation ProcedureThis section describes how to install the SetUp Software to Windows 2000 using th

7-37E DV-90-IMHow to Use the Setup Software7-1 Installation Procedure5 Select “I accept the terms in the license agreement”, and click [Next].6 Check

7-4E DV-90-IM7How to Use the Setup Software8 Check that the screen “InstallShield Wizard Completed” is displayed, and click [Finish].9 Start the SetUp

7-5E DV-90-IM7How to Use the Setup Software7-2 Overview of Operation MethodThis section describes the screens of the SetUp Software and the startup pr

7-6E DV-90-IM7How to Use the Setup SoftwareMenu CommandsThis section describes the menu commands of the SetUp Software. File menu Edit menu Communi

7-7E DV-90-IM7How to Use the Setup Software7-3 Setting ProcedureThe SetUp Software performs various settings required for using the DV-90.This section

7-8E DV-90-IM7How to Use the Setup Software7-3 Setting ProcedureOperation SettingsIn the operation settings, the verification setting, PORT1/PORT2 se

7-97E DV-90-IMHow to Use the Setup Software(Serial Output (Detail))*ASCII input and hexadecimal inputThe input type can be selected from either “ASCII

7-10E DV-90-IM7How to Use the Setup Software7-3 Setting Procedure PORT1/PORT2 SettingsThe items displayed in PORT1 and PORT2 vary depending on the “

7-117E DV-90-IMHow to Use the Setup Software7-3 Setting Procedure(Communication Setting (Detail))(Connect Unit: Code Reader)Receive Data FormatRTS/CT

1-3E DV-90-IM1Getting Started1-2Overview of DV-90 FunctionsAutomated Product Selection at an Assembly WorkstationBy reading the barcode attached to an

7-12E DV-90-IM7How to Use the Setup Software7-3 Setting Procedure(Connect Unit: PLC Link)DM AddressPLC Trigger AreaPLC Unit ID• DM AddressSets the DM

7-137E DV-90-IMHow to Use the Setup Software7-3 Setting Procedure I/O SettingsREMOTE KeyActive Record Select NotifyPreset Mode NotifyOutput Delay Ti

7-14E DV-90-IM7How to Use the Setup Software7-3 Setting Procedure Optional SettingsBacklight Auto OffKey ProtectBuzzer• Backlight Auto OffSets the i

7-157E DV-90-IMHow to Use the Setup Software7-3 Setting ProcedureMaster SettingsThe master data of the DV-90 is set in the Master Settings.Data and r

7-16E DV-90-IM7How to Use the Setup Software When the record field is displayed in red Registering the master data using “!” and “?”.When inputting

7-177E DV-90-IMHow to Use the Setup Software7-3 Setting Procedure Setting Verify Limit/Date CompareTo configure the settings of Verify Limit/Date Co

7-18E DV-90-IM7How to Use the Setup Software7-3 Setting Procedure6 Under “Verify Limit” select “Logic”.When “Limit” is selected for “Type” of “Verify

7-197E DV-90-IMHow to Use the Setup Software7-3 Setting Procedure Showing/hiding the details of Master 1 to 3The content of “Verify Limit” of the da

7-20E DV-90-IM7How to Use the Setup Software2 Select “Date Compare”.3 Configure the settings.4 When the [OK] button is clicked, “Date Compare” is acti

7-21E DV-90-IM7How to Use the Setup Software7-4 Sending and Receiving the SettingsThe settings and the master data can be sent and received using the

1-4E DV-90-IM1Getting Started1-2 Overview of DV-90 FunctionsPreventing Mixing with Other Products at a Packaging Machine By reading the barcode print

7-22E DV-90-IM7How to Use the Setup Software7-4 Sending and Receiving the Settings• When the DV-90 is connected to the PC via USB• Interface : Select

7-237E DV-90-IMHow to Use the Setup Software5 The following screen is displayed.6 When “Completed!” is displayed, click the [OK] button.

7-24E DV-90-IM7How to Use the Setup Software7-4 Sending and Receiving the Settings2 Select the “Master record count” to be received, and click the [O

7-25E DV-90-IM7How to Use the Setup Software7-5Saving/Reading/Printing the Setting FilesThe setting files in which the setting contents are recorded c

7-26E DV-90-IM7How to Use the Setup Software7-5 Saving/Reading/Printing the Setting FilesReading the Setting File1 From the [File] menu, select [Open

7-277E DV-90-IMHow to Use the Setup Software7-5 Saving/Reading/Printing the Setting FilesPrinting the Setting File1 From the [File] menu, select [Pri

7-28E DV-90-IM7How to Use the Setup Software7-6 Quick Setup Code of the DV-90All the settings in the SetUp Software can be printed as barcodes. By sim

7-297E DV-90-IMHow to Use the Setup Software7-6 Quick Setup Code of the DV-903 Configure the print settings, and click the [OK] button.The Quick Setu

7-30E DV-90-IM7How to Use the Setup SoftwareReading the Quick Setup Codes1 Press the key for one second to display the setting menu.2 Press the ke

7-31E DV-90-IM7How to Use the Setup Software7-7Setting Procedure for the BL Series Using Quick Setup CodeThe contents set in the BL Series SetUp Softw

1-51E DV-90-IMGetting Started1-2 Overview of DV-90 Functions Preventing Misplacement of Raw MaterialReading the barcodes on a batch instruction sheet

7-32E DV-90-IM7How to Use the Setup Software7-7 Setting Procedure for the BL Series Using Quick Setup Code3 Click the [Select File] button. Select th

7-337E DV-90-IMHow to Use the Setup Software7-7 Setting Procedure for the BL Series Using Quick Setup Code4 Click the [Print Out] button.The Quick Se

7-34E DV-90-IM7How to Use the Setup Software3 Read the printed Quick Setup Codes from top to bottom using the barcode reader.When all the barcodes are

7-35E DV-90-IM7How to Use the Setup Software7-8 TerminalThe communication status between the DV-90 and the PC can be checked.Receiving the Data1 Confi

7-36E DV-90-IM7How to Use the Setup Software7-8 Terminal3 Read a data item using the code reader.The received data is displayed. A history of up to 1

7-377E DV-90-IMHow to Use the Setup Software7-8 Terminal2 From the [Communication] menu, select [Terminal].The “Terminal” screen is displayed.3 Input

7-38E DV-90-IM7How to Use the Setup Software4 A history of the commands already sent can be viewed.Clicking in [Command] displays the history of pre

7-39E DV-90-IM7How to Use the Setup Software7-9 Error Display ListThis section describes the messages displayed on the SetUp Software when an error oc

7-40E DV-90-IMMEMO7How to Use the Setup Software

8-188E DV-90-IMSerial CommunicationThis chapter describes the method for communicating with external devices by using the serial interface of the DV-9

1-6E DV-90-IM1Getting Started1-2 Overview of DV-90 FunctionsPreventing Mispackaging in a Manual Packaging ProcessReading the barcodes on the packagin

8-2E DV-90-IM8Serial Communication8-1 Serial CommunicationWith serial communication, you can send data to the PC, and control the DV-90 by sending com

8-38E DV-90-IMSerial Communication8-1 Serial Communication Using the USB1 Install the USB driver to the PC.Refer to page 3-13 for the installation p

8-4E DV-90-IM8Serial Communication8-2 Data Communication DetailsThis section describes the communication protocol and communication format.Communicati

8-58E DV-90-IMSerial Communication8-2 Data Communication Details ACK/ANK protocolUse (06H) instead of PASS in the PASS/RTRY protocol, and use (15H

8-6E DV-90-IM8Serial Communication8-2 Data Communication DetailsType of Output DataSelect the output data from the types shown below.Difference in Se

8-78E DV-90-IMSerial Communication Step verification(First data reading)Read OK No output 3-points-A verification(First data reading)Verify

8-8E DV-90-IM8Serial Communication8-2 Data Communication Details 3-points-B verification(First data reading) 2-point verification(First data readin

8-98E DV-90-IMSerial Communication8-2 Data Communication DetailsAdditional InformationThe “Date”, “Time”, and “Port” can be added to the data to be s

8-10E DV-90-IM8Serial Communication8-3 Command Communication DetailsIn the command communication, there are “Direct control commands” to control the D

8-118E DV-90-IMSerial Communication8-3 Command Communication DetailsDescription of Direct Control Commands * Sends a trigger control command to a barc

1-71E DV-90-IMGetting StartedVerifying the Assembly Instruction by Comparing with the Customer Order Sheet (Kanban)In the process of assembling produc

8-12E DV-90-IM8Serial Communication8-3 Command Communication DetailsCommunication Procedure for the Setting CommandsThe following procedure is used fo

8-138E DV-90-IMSerial Communication8-3 Command Communication DetailsSetting Command Description End/Initialization of the setting mode Settings rele

8-14E DV-90-IM8Serial Communication8-3 Command Communication Details Settings relevant to PORT1/PORT2Function Sending command Response NotesPORT Uni

8-158E DV-90-IMSerial Communication8-3 Command Communication Details Settings relevant to code readerFunction Sending command Response NotesReceive

8-16E DV-90-IM8Serial Communication8-3 Command Communication Details Settings relevant to serial communication * Refer to the ASCII CODE TABLE (Appen

8-178E DV-90-IMSerial Communication8-3 Command Communication Details Settings relevant to PLC link  Settings relevant to I/O Function Sending comman

8-18E DV-90-IM8Serial Communication8-3 Command Communication Details Settings relevant to equipment performance Function Sending command Response No

8-198E DV-90-IMSerial Communication8-3 Command Communication Details Master table settingsMaster table registrationThe master table registration comm

8-20E DV-90-IM8Serial Communication8-3 Command Communication Details(Representation of data) Underlined numbers are default va

8-218E DV-90-IMSerial Communication8-3 Command Communication DetailsWhen using Verify Normal, if you want to specify the number written above in Recor

IntroductionThis manual describes instructions on basic usage of the DV-90, its operation procedures, warnings and precau-tions. Be sure to read this

1-8E DV-90-IM1Getting StartedChecking the Print Quality of the Expiration Date or Manufactured DateWhether the expiration date or manufactured date in

8-22E DV-90-IMMEMO8Serial Communication

9-199E DV-90-IMPLC LinkThis chapter describes how to control the PLC link.9-1 What is a PLC Link?...

9-2E DV-90-IM9PLC Link9-1 What is a PLC Link?This section presents an overview of the PLC and describes how to control it.What is a PLC Link?The PLC l

9-39E DV-90-IMPLC Link9-1 What is a PLC Link?Accessible DevicesThe following range of devices can be accessed through a PLC link.KV-10/16/24/40 DM000

9-4E DV-90-IM9PLC Link9-2 Device AssignmentThis section describes device assignment.The devices are assigned as follows with the “DM head address” set

9-59E DV-90-IMPLC Link9-2 Device AssignmentThe area in which the data is written is assigned as follows with the “Write head address” specified in “X

9-6E DV-90-IM9PLC Link9-2 Device AssignmentDetails on DM Assignment DM that reports the start of operation to the PLC• This is the flag that reports

9-79E DV-90-IMPLC Link9-2 Device Assignment DMs that report the head address of the data write destination• Specify the head address of the area to

9-8E DV-90-IM9PLC Link9-2 Device Assignment DMs that control the read trigger• “X+06 Read Trigger Notice Area” is used when feeding the start readin

9-99E DV-90-IMPLC Link(Usage 2)“X+07” is the flag that monitors whether or not the DV-90 has correctly recognized “X+06”.When turning on and off the t

1-9E DV-90-IM1Getting Started1-3DV-90 Layout Panel side➀ Record No. indicator LEDs ... Display the record No. being registered, matched rec

9-10E DV-90-IM9PLC Link9-2 Device Assignment DMs that report to the PLC that the data writing is completed• “X+08 to +10” are the DMs that report to

9-119E DV-90-IMPLC Link9-2 Device Assignment(Sequence processing)➀Write “1” in “X+08” before starting an operation, and select “Sequence processing”.

9-12E DV-90-IM9PLC Link9-2 Device Assignment DM that detects the occurrence of a reset• “1” is written when the DV-90 starts up.The occurrence of a

9-139E DV-90-IMPLC Link9-2 Device Assignment DM that checks the current operation status• The current operation status of the DV-90 can be checked.•

9-14E DV-90-IM9PLC Link9-2 Device Assignment DMs in which various data is written• All data shown above is written in binary code.For the timing of

9-159E DV-90-IMPLC Link9-2 Device Assignment DMs in which data is written• The DMs are assigned with the addresses specified in “X+01 to +03” at th

9-16E DV-90-IM9PLC Link9-2 Device Assignment• “ERROR” is written when a read error occurs in the code reader connected to PORT1.When Y1 is 300 and Da

9-17E DV-90-IM9PLC Link9-3 Data Write Timing Note that the following flowchart shows the writing of data to the PLC when viewed from the DV-90.Operati

9-18E DV-90-IM9PLC Link9-3 Data Write Timing Step verification, 2-point verification Ye sNo (Read Error)Ye sNo (Read Error)Wait for the data from

9-199E DV-90-IMPLC Link9-3 Data Write TimingThe data to be written is as shown below.“-” indicates that the data will not be overwritten. (The previo

1-10E DV-90-IM1Getting Started Terminal side➆ USB port ... Connects to the USB port on a PC. ➇ I/O terminal

9-20E DV-90-IM9PLC Link9-3 Data Write Timing 3 points-A verification Ye s Ye sNo (Read Error) Ye sNo (Read Error) Ye sNo (Verify NG) Ye sNo (Selecte

9-219E DV-90-IMPLC Link9-3 Data Write TimingThe data to be written is as shown below.“-” indicates that the data will not be overwritten. (The previo

9-22E DV-90-IM9PLC Link 3 points-B verification Ye sNo(Read Error)Ye sNo(Read Error) Ye sNo(Read Error) Ye sNo(Verify NG)Ye sNo(Selected Master Verif

9-239E DV-90-IMPLC Link9-3 Data Write TimingThe data to be written is as shown below.“-” indicates that the data will not be overwritten. (The previo

9-24E DV-90-IM9PLC Link9-4 Supported PLC ModelsThe DV-90 can be linked with the following PLCs. Keyence Mitsubishi ElectricSeries name Connecting me

9-259E DV-90-IMPLC Link9-4 Supported PLC Models OmronSeries name Connecting method ModelSYSMAC C CPU internal port C200HS-CPU21/23/31/33 Upper link

9-26E DV-90-IM9PLC Link9-5 SettingsSettings of the DV-90Set the DV-90 as follows.1 Set “PORT2 Unit” in “Main” to “PLC Link”.2 Select the “PLC Type” in

9-279E DV-90-IMPLC Link9-5 SettingsSettings for the KV Series Settings of the DV-90Connecting PLCKV programming port PORT2 connecting devicePLC Link

9-28E DV-90-IM9PLC Link9-5 SettingsSettings for the MELSEC Series Settings of the DV-90 A1SJ71 (U) C24-R2/PRF, A1SCPUC24-R2  AJ71C24-S , A2CCPUC24

9-299E DV-90-IMPLC Link9-5 Settings AJ71QC24 (-R2), A1SJ71QC24 (-R2) QJ71C24 (-R2), QJ71C24N (-R2/R4)Set the communication conditions on the GX Dev

1-11E DV-90-IM1Getting Started1-4System Configuration and Connectable DevicesThe DV-90 can be used with the following devices.Numbers in parentheses (

9-30E DV-90-IM9PLC Link9-5 SettingsSettings for the SYSMAC Series Settings of the DV-90 C120-LK201-V1* The data length, parity, and stop bit are fix

9-319E DV-90-IMPLC Link9-5 Settings C500-LK201-V1 , C500-LK203 * In the C500-LK201-V, the data length, parity, and stop bit are fixed to 7, even, an

9-32E DV-90-IM9PLC Link9-5 Settings CQM1 (H), C200HS, C200HE, C200HG, C200HX (CPU internal port), CQM1-SCB41, C200HW-COM02/04/05/06 (commun

9-339E DV-90-IMPLC Link9-5 Settings CJ Series, CS1 Series (CPU internal port)CS1W-SCB21/41 (communication board),CS1W-SCU21 (communication unit)(DIP

9-34E DV-90-IM9PLC Link9-6 PLC Link Communication TimeThis section describes the communication time of the DV-90. The communication time required for

9-35E DV-90-IM9PLC Link9-7 PLC Link TroubleshootingWhen communication cannot be established via the PLC link, perform the following steps.➀Read data w

9-36E DV-90-IM9PLC LinkCheck that the values to be written in +01, +02, and +03 are within the range supported by the DV-90 and the PLC. ( Refer to 9

Appendix-1Appendix1 Specifications ... A-22 Dimensions...

Appendix-2E DV-90-IMAppendix 1 SpecificationsThis section describes the specifications of the DV-90.ModelDV-90NE (NPN output type)DV-90PE (PNP output

Appendix-3E DV-90-IMAppendix 2 DimensionsDV-90Panel Cutout 2695.55.95.921.8116.8145.584.8134.86(64.2)52.3262626.8Panel thickness1.6 to 4.0 mm4-φ3.4

1-12E DV-90-IM1Getting Started∗ 1 PORT1 can connect a barcode reader.∗ 2 PORT2 can connect either a barcode reader, PC or PLC.∗ 3 USB can connec

Appendix-4E DV-90-IMAppendix 3 Error MessagesThis message is displayed when an error occurs upon connection with the code reader(BL-1300/700/600/180

Appendix-5E DV-90-IMAppendix 4 ASCII Code TableHTVTFirst 4 bitsHexadec-imalBinaryLast 4 bits

Appendix-6E DV-90-IMAppendix 5 Setting Item ListThis section describes the items that can be set in the DV-90.Basic settings Verify Type Normal

Appendix-7E DV-90-IMAppendix5 Setting Item ListVerify PORT1PORT2I/O Parallel Out Bit Binary BCD Output Data Input Data

Appendix-8E DV-90-IMAppendix5 Setting Item ListOptional Back Light Auto OFF Continue Key Protect (PRESET KEY) 0s 1s 3

Appendix-9E DV-90-IMAppendix 6 Factory Setting ListThis section describes the factory settings of the DV-90.Basic settings Verify PORT1 Verify Typ

Appendix-10E DV-90-IMAppendix6 Factory Setting ListPORT2I/O Optional Baud Rate9600 bits/sCOM2 FormatData length: 7 bits Parity check: Even S

Appendix-11E DV-90-IMAppendix7 PLC Program ExamplesThis section describes PLC program examples under the conditions as shown below.Settings of the DV

Appendix-12E DV-90-IMAppendix7 PLC Program Examples#0001DWDM00000000#0001DWDM0006CR2002(2002)DM009LDA#0001CMPCR2002(2002)#0000DWDM0011#0001DWDM0012CR

Appendix-13E DV-90-IMAppendix7 PLC Program ExamplesMELSEC SeriesInitialization of the DM•Set the “Data write head address” as D100.•Set the “Data wri

2-122Initial Setup of the Code ReaderThis chapter describes the basic setup for connecting a code reader to the DV-90. 2-1 Code Reader Setup Basics ..

Appendix-14E DV-90-IMAppendix7 PLC Program ExamplesData read process•When the “Write Complete Confirmation Flag” dis-plays “1: Data Write Complete”,

Appendix-15E DV-90-IMAppendix7 PLC Program ExamplesSYSMAC SeriesInitialization of the DM•Set the “Data write head address” as DM100.•Set the “Data wr

Appendix-16E DV-90-IMAppendixControl of the read triggerInput 0000 controls the read trigger.Data read process• When the “Write Complete Confirmation

Appendix-17E DV-90-IMAppendix7 PLC Program ExamplesSet the Active record number to 3 from Input 0003.@MOV0003#0000DM0011@MOV&3DM0012END

Appendix-18E DV-90-IMAppendix8 Preset Mode Status OutputBy enabling “Preset mode status output” (refer to 6-11), the registration status in the preset

Appendix-19E DV-90-IMAppendix9 Active Record Selection NotificationBy enabling “Active Notice”, the selection of the active record using the code read

Appendix-20E DV-90-IMAppendix10 Test BarcodesThese barcodes are for testing purposes. Use them to verify operation of your code reader and the DV-90.

Appendix-21AppendixE DV-90-IM11 IndexNumerics2-Point Verification ...4-34, 8-83-Point-A Verification ...

Appendix-22E DV-90-IMAppendixHHeader ...7-9Help menu ...

Appendix-23E DV-90-IMAppendixRS-232C (PORT1) ...1-10RS-232C (PORT2) ...

2-22Initial Setup of the Code ReaderE DV-90-IM2-1 Code Reader Setup Basics This section describes the preparation flow before using the DV-90. 1 In th

Appendix-24E DV-90-IMMEMOAppendix

WARRANTIES AND DISCLAIMERS(1) KEYENCE warrants the Products to be free of defects in materials and workmanship for a period of one (1) year from the d

Copyright (c) 2009 KEYENCE CORPORATION. All rights reserved.10259E 1113-2 96M10260 Printed in Japan

2-32Initial Setup of the Code ReaderE DV-90-IM3 Connect the code reader to PORT1 of the DV-90. ⇒ Refer to 3-8.Turn off the power of the DV-90 when c

2-42Initial Setup of the Code ReaderE DV-90-IM7 Wire the trigger input (input to starting reading). ⇒ Refer to 3-4. • If a hand-held reader is conne

2-52Initial Setup of the Code ReaderE DV-90-IMHow to Detect the Communication Setting AutomaticallyWhen the communication setting of the connected BL-

1E DV-90-IMSafety Precautions Tips on Correct UsezHandling •Do not attempt to open or modify the DV-90. Doing so may cause fire and electric shock.

2-62Initial Setup of the Code ReaderE DV-90-IM2-2Setting Procedure of the BL Series and the SR SeriesWhen changing the settings of theBL-1300/700/600/

2-72Initial Setup of the Code ReaderE DV-90-IM5 Configure the PC communication conditions on the setup software. BL SetUp SoftwareConfigure “PC Port

2-82Initial Setup of the Code ReaderE DV-90-IM2-3Read Test Procedure of the BL Series and the SR SeriesThis section describes how to perform the read

2-92Initial Setup of the Code ReaderE DV-90-IM2 Press the key on the DV-90 and the com-mand to be sent to the BL Series or the SR Series is displaye

2-102Initial Setup of the Code ReaderE DV-90-IM5 To exit the reading rate test mode, press the key on the DV-90, select “QUIT” with the or key, an

3-133E DV-90-IMConnections and MountingThis chapter describes the connection of the devices and mounting procedure of the DV-90.3-1 I/O Terminal Conne

3-2E DV-90-IM3Connections and Mounting3-1 I/O Terminal ConnectionI/O Terminal Pin AssignmentNo. Label Name No. Label Name1 TRG1 Trigger input 1 15 REA

3-3E DV-90-IM3Connections and Mounting Connecting the cableConnect the cable by using a screwdriver as shown below. (Tightening torque: 0.2 Nm)3-1 I

3-43Connections and MountingE DV-90-IM3-1 I/O Terminal ConnectionWiring the Input TerminalsConnection diagram

3-53Connections and MountingE DV-90-IM3-1 I/O Terminal ConnectionWiring the Output Terminals (NPN Open Collector Type)The DV-90NE (NPN open collector

2E DV-90-IMCE Marking and UL Conformity CE Marking It is confirmed that the DV-90 Series satisfies the requirements of the EU Directive, and conforms

3-63Connections and MountingE DV-90-IM3-1 I/O Terminal ConnectionWiring the Output Terminals (PNP Open Collector Type)The DV-90PE (PNP open collector

3-73Connections and MountingE DV-90-IM* Refer to page 6-5.* Refer to page 6-5.3-2 RS-232C Interface ConnectionThe DV-90 is equipped with two RS-232C i

3-83Connections and MountingE DV-90-IMConnecting the Code ReaderConnect the code reader to PORT1.When “PORT2 Unit” is set to “Code Reader”, a code rea

3-93Connections and MountingE DV-90-IM Connecting the BL-1300 Series or the SR-600/500 SeriesTo connect the BL-1300 Series or the SR-600/500 Series,

3-103Connections and MountingE DV-90-IM Connecting code readers of other manufacturersRefer to the manual of the connecting code reader, and also ref

3-113Connections and MountingE DV-90-IM Connecting the KV programming port Connecting the KV-L21V/L20V/L20R/N10LOP-24045 (1m)OP-24025 (5m)OP-26486KV

3-123Connections and MountingE DV-90-IM3-2 RS-232C Interface Connection Connecting the MELSEC SerieszAOJ2-C214-S1 zA2CCPUC24(-PRF)AJ71C24(-S) A1SJ7

3-133Connections and MountingE DV-90-IM3-3USB Interface Connection/Driver InstallationThe USB interface only allows the connection to a PC.Using the U

3-143Connections and MountingE DV-90-IM3-3 USB Interface Connection/Driver Installation3 When the DV-90 is connected to the PC, the message “New Hard

3-153Connections and MountingE DV-90-IM3-3 USB Interface Connection/Driver Installation6 Select “Specify a location” and click [Next >].7 Specify

3E DV-90-IMSoftware Licensing AgreementsRead the following licensing agreement carefully before using this software.By using the software, you signify

3-163Connections and MountingE DV-90-IM3-3 USB Interface Connection/Driver Installation10 Check the “Found New Hardware Wizard” screen and click [Fin

3-173Connections and MountingE DV-90-IM3-3 USB Interface Connection/Driver Installation14 Select “Specify a location” and click [Next >].15 Specif

3-183Connections and MountingE DV-90-IM3-3 USB Interface Connection/Driver Installation18 When the installation is complete, the notification “Your n

3-193Connections and MountingE DV-90-IM3-3 USB Interface Connection/Driver Installation Windows XP1 Turn on the power of the PC and start Windows XP

3-203Connections and MountingE DV-90-IM3-3 USB Interface Connection/Driver Installation5 Select “Search for the best driver in these locations”. Sele

3-213Connections and MountingE DV-90-IM3-3 USB Interface Connection/Driver Installation9 “Found New Hardware Wizard” automatically starts. Select “In

3-223Connections and MountingE DV-90-IM3-3 USB Interface Connection/Driver Installation13 When the installation is complete, the notification “Your n

3-23E DV-90-IM3Connections and Mounting3-3 USB Interface Connection/Driver InstallationUninstalling the USB Driver SoftwareThe uninstalling procedure

3-243Connections and MountingE DV-90-IM3-4 Wiring the Power Supply TerminalsConnect the DV-90 to a 24V DC power supply with a minimum output rating of

3-253Connections and MountingE DV-90-IM3-5 Mounting the DV-90This section describes how to mount the DV-90. Panel-mounting procedureMount the DV-90 t

4E DV-90-IMSafety Precautions ...

3-263Connections and MountingE DV-90-IM3-5 Mounting the DV-90 Mounting procedure using the mounting screwsWhen not installing the DV-90 on a panel,

4-144E DV-90-IMBasic FunctionsThis chapter describes the basic functions of the DV-90 and their method of operation.4-1 Verification Function ...

4-2E DV-90-IM4Basic Functions4-1 Verification FunctionThis section describes the functions of the DV-90 that determine how the DV-90 interprets the sc

4-34E DV-90-IMBasic Functions4-1 Verification Function• Reference dataDefines the actual data displayed when the read data matches the master data. (

4-4E DV-90-IM4Basic Functions4-2 Normal VerificationThis is used to compare and verify the master data, which is registered (preset) beforehand, to re

4-54E DV-90-IMBasic Functions4-2 Normal Verification4 Specify the normal verification function.Place the cursor on “Normal” by pressing the or key.

4-6E DV-90-IM4Basic Functions4-2 Normal Verification2 Read the barcode with the code reader.The buzzer is sounded, and the read data is setas the mas

4-74E DV-90-IMBasic Functions4-2 Normal VerificationPresetting from the Desired Record NumberThe master data can be preset from the desired number.1

4-8E DV-90-IM4Basic Functions4-2 Normal VerificationWorking with the Normal Verification Function (Verification Mode)Start reading the master data af

4-94E DV-90-IMBasic FunctionszWhen the read error check is set* This occurs on the BL-1300/700/600/500/180 and the SR-500.• LED Display...“Err” is dis

5E DV-90-IM4-1 Verification Function ...

4-10E DV-90-IM4Basic Functions4-2 Normal Verification2 Display the verification settings menu.Press the or key to place the cursor on“2 Verify”.

4-114E DV-90-IMBasic Functions4-2 Normal VerificationTiming Chart for Parallel OutputAfter reading the data, execute parallel output at the following

4-12E DV-90-IM4Basic Functions2 Display the verification settings menuPress the or key to place the cursor on“2 Verify”.Then, press the key.3 Di

4-13E DV-90-IM4Basic Functions4-3 Active VerificationThis function is used to select only one preset from the registered master data, and to confirm i

4-14E DV-90-IM4Basic Functions4-3 Active Verification4 Specify the active verification functionPlace the cursor on “1: Active” by pressing the and

4-154E DV-90-IMBasic Functions4-3 Active Verification2 Determine the active record.Determine the active record by pressing the key.The selected act

4-16E DV-90-IM4Basic Functions3 Set the active record.Set the active record by pressing the key.The selected active record number is displayed on th

4-17E DV-90-IM4Basic Functions4-4 Step Verification FunctionThis function is used to verify two codes and determine if they match.Step Verification Fu

4-18E DV-90-IM4Basic Functions4-4 Step Verification Function4 Set the step verification function.Place the cursor on “1: Active” by pressing the and

4-194E DV-90-IMBasic Functions4-4 Step Verification Function3 Read the barcode.(Second reading)Compares and verifies the data from both read-ings, OK

6E DV-90-IMInput Limitation Function ...

4-20E DV-90-IM4Basic FunctionsTiming Chart for Parallel OutputAfter reading the data, execute parallel output at the following timing:➀...Output

4-21E DV-90-IM4Basic Functions4-5 3-Point-A Verification FunctionThis function is used to compare and verify three master data items in the order that

4-22E DV-90-IM4Basic Functions4-5 3-Point-A Verification Function3 Specify the verification type.Display “Verify Type” by pressing the or key. Then

4-234E DV-90-IMBasic Functions4-5 3-Point-A Verification Function3 Read the second code (Master data 2) with the code reader.The buzzer is sounded,

4-24E DV-90-IM4Basic Functions4-5 3-Point-A Verification FunctionWorking with the 3-Point-A Verification Function (Verification Mode)The operation us

4-254E DV-90-IMBasic Functions4-5 3-Point-A Verification Function3 Read the barcode. [Verify OK](Second reading)This is verified with Master data 2.z

4-26E DV-90-IM4Basic Functions4-5 3-Point-A Verification FunctionzAt Verify NGOutputs representing “999” (NG and VerifyNG) are turned ON.Then the uni

4-274E DV-90-IMBasic Functions4-5 3-Point-A Verification FunctionTiming Chart for Parallel OutputAfter reading the data, execute parallel output at t

4-28E DV-90-IM4Basic Functions4-6 3-Point-B Verification FunctionThis function is used to compare and verify the master data in the order that the dat

4-294E DV-90-IMBasic Functions4-6 3-Point-B Verification Function3 Specify the verification type.Display “Verify Type” by pressing the or key. Then

7E DV-90-IMOperation Settings...

4-30E DV-90-IM4Basic Functions4-6 3-Point-B Verification Function2 Read the barcode.(First data reading)This is verified with Master data 1.zAt Verif

4-314E DV-90-IMBasic Functions4-6 3-Point-B Verification Function3 Read the barcode.(Second data reading)This is verified with Master data 2.zAt Veri

4-32E DV-90-IM4Basic Functions4-6 3-Point-B Verification Function4 Read the barcode. (Third reading)This is verified wit

4-334E DV-90-IMBasic Functions4-6 3-Point-B Verification FunctionTiming Chart for Parallel OutputParallel output is executed at the timing shown belo

4-34E DV-90-IM4Basic Functions4-7 2-Point Verification FunctionThis function is used to compare and verify two data items with a group of two master d

4-354E DV-90-IMBasic Functions4-7 2-Point Verification Function5 Exit the setting mode.Press the key twice.Setting of the 2-point verification func

4-36E DV-90-IM4Basic Functions4-7 2-Point Verification Function4 Exit the preset mode.Press the key after presetting is completed. The preset LED t

4-374E DV-90-IMBasic Functions4-7 2-Point Verification Function2 Read the barcode. (First data reading)This is verified with Master data 1.zAt Verify

4-38E DV-90-IM4Basic Functions4-7 2-Point Verification FunctionTiming Chart of Parallel OutputAfter reading the data, execute parallel output at the

5-155E DV-90-IMExtended FunctionsThis chapter describes the extended functions of the DV-90.5-1 Reference Data Function .........