Keyence DV-90 User Manual Page 155
- Page / 262
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
7-17
7
E DV-90-IM
How to Use the Setup Software
7-3 Setting Procedure
Setting Verify Limit/Date Compare
To configure the settings of Verify Limit/Date Compare , refer to pages 5-9 and 5-10.
The setting procedure using the SetUp Software is described below.
1 Input the data.
For Date Compare, enter the data in the range between –10000 and +10000 (six digits including
+ or –).
+10 days → +00010
+100 days → +00100
2 Under “Verify Limit” select “Type”.
3 Under “Verify Limit” select “Direction”.
4 Under “Verify Limit” enter “Limit Start” (1 to 500).
5 Under “Verify Limit” enter “Limit Digits” (1 to 500).
When “Date Compare” is selected for “Type” of “Verify Limit”, “Limit Digits” is fixed to “6”.
Example
- User’s Manual 1
- Introduction 2
- Safety Precautions 3
- CE Marking and UL Conformity 4
- Software Licensing Agreements 5
- Chapter 1 Getting Started 6
- Chapter 4 Basic Functions 7
- Chapter 5 Extended Functions 7
- Chapter 6 Setting 8
- Chapter 9 PLC Link 9
- Appendix 10
- Manual Structure 11
- Getting Started 13
- Checking the Package Contents 14
- Overview of DV-90 Functions 15
- Other uses 16
- DV-90 Layout 21
- Terminal side 22
- KV-B16XA 23
- 2-1 Code Reader Setup Basics 26
- 1234567890 27
- PC Direct 30
- *CR1<> 30
- PORT2<>USB* 30
- < SEND 31
- Read Test Using the Key 32
- Connections and Mounting 35
- 3-1 I/O Terminal Connection 36
- I/O Terminal Pin Assignment 36
- Connecting the cable 37
- Wiring the Input Terminals 38
- RS-232C Interface Connection 41
- Connecting the Code Reader 42
- Connecting a PC or PLC 44
- OP-24045 (1m) 45
- OP-24025 (5m) 45
- OP-26486 45
- ) A1SJ71(U)C24 46
- Notes on Connecting the DV-90 47
- → “Device Manager (D)” 52
- Windows XP 53
- → “Device Manager” 56
- Fork type 58
- Ring type 58
- 6.0 mm or less 58
- 3-5 Mounting the DV-90 59
- Panel surface 60
- Basic Functions 61
- 4-1 Verification Function 62
- 301000Δ 101234567 63
- 4-2 Normal Verification 64
- Normal Verification Function 64
- Verify Type 65
- 4 Exit the preset mode 66
- Init MasterRec 67
- Yes-ENT No-ESC 67
- (Ready to Read) 68
- 1122334455 68
- Confirming the Master Data 69
- Counter Function 69
- Interlock Function 71
- Parallel Out 72
- Interlock 72
- Flashing 72
- 4-3 Active Verification 73
- Active Verification Function 73
- Selecting the Active Record 74
- 1 Select the active record 75
- (Ready to Read) 76
- Active record 76
- Step Verification Function 77
- [Verify OK] 79
- [Verify NG] 79
- Read Error(CR1) 79
- 1 Press the key 82
- 4 Read the barcode 85
- 2-point Verification Function 94
- 1 Press the key 95
- Verify OK Verify OK 98
- Select Master NG/Read_Error 98
- Verify NG/Read_Error 98
- 5-1 Reference Data Function 100
- Reference Data Function 100
- E DV-90-IM 101
- Extended Functions 101
- Input Limitation Function 102
- Forward Reverse 103
- Verify Limitation Function 107
- Date Compare Function 108
- Read Quality Check Function 112
- 1 Move to the setting mode 113
- 5 Exit the setting mode 113
- 1 Move to the test mode 114
- QLT : 75% 115
- 12345678 115
- (Q-Err) 115
- 1 Move to the preset mode 116
- 2 Move to the edit mode 117
- 4 Exit the edit mode 118
- 5 Exit the detail mode 118
- 6 Exit the preset mode 118
- Setting the Verify Limit 119
- Setting “Date Compare” 120
- 6 Set the detail screen 121
- 7 Exit the preset mode 121
- 3 Set the Input Port Limit 122
- 4 Exit the detail mode 122
- 5 Exit the preset mode 122
- Setting the Output Number 123
- 6-1 Setting Procedures 126
- To Start the Setting Menu 126
- To Exit the Setting Menu 127
- Menu List 128
- Main Setting Menu 128
- Setting item details 129
- Verification Setting Menu 130
- Bit output 131
- Binary output 131
- PORT1/PORT2 Setting Menu 132
- I/O Settings Menu 135
- Options Setting Menu 136
- Code Setting Menu 137
- Initializing Settings 137
- How to Use the SetUp Software 139
- 7-1 Installation Procedure 140
- How to Use the Setup Software 141
- 9 Start the SetUp Software 142
- Start and Quit 143
- Menu Commands 144
- 7-3 Setting Procedure 145
- Basic Settings 145
- Operation Settings 146
- (Serial Output (Detail)) 147
- Data Length 148
- Baudrate 148
- Stop Bit Default 148
- DM Address 150
- PLC Trigger Area 150
- PLC Unit ID 150
- I/O Settings 151
- Backlight Auto Off 152
- Key Protect 152
- Master Settings 153
- Important 154
- 1 Input the data 155
- About the Right-Click Menu 156
- 2 Select “Master1 Hide” 157
- Sending the Settings 159
- 3 Click the [Send] button 160
- Receiving the Settings 161
- Saving the Setting File 163
- Reading the Setting File 164
- Printing the Setting File 165
- Quick Setup Code of the DV-90 166
- Reading the Quick Setup Codes 168
- Reading the Quick Setup Code 171
- CR Quick Setup 172
- 1/ 2 172
- Send Config? 172
- Yes-ENT No-ESC 172
- Now Sending 172
- 7-8 Terminal 173
- Receiving the Data 173
- Sending Commands 174
- (Up to 20 commands) 176
- 7-8 Terminal 176
- 7-9 Error Display List 177
- Serial Communication 179
- 8-1 Serial Communication 180
- Communication Form 180
- Using the USB 181
- Communication Protocol 182
- Send Data Format 183
- Type of Output Data 184
- Step verification 185
- 3-points-A verification 185
- 3-points-B verification 186
- 2-point verification 186
- Additional Information 187
- Communication Format 188
- Setting Command Description 191
- Settings relevant to I/O 195
- Master table settings 197
- (Command formats) 197
- PLC Link 201
- 9-1 What is a PLC Link? 202
- What is a PLC Link? 202
- Supported PLCs (Series Names) 202
- Accessible Devices 203
- 9-2 Device Assignment 204
- DM Assignment List 204
- 9-2 Device Assignment 205
- Details on DM Assignment 206
- Reference 208
- Refer to 9-10.) 209
- 9-3 Data Write Timing 217
- 9-3 Data Write Timing 218
- First data reading 219
- Second data reading 219
- 3 points-A verification 220
- Third data reading 221
- 3 points-B verification 222
- 9-4 Supported PLC Models 224
- 9-5 Settings 226
- Settings of the DV-90 226
- Settings for the KV Series 227
- Settings of the DV-90 228
- C120-LK201-V1 230
- C200H-LK201-V1 230
- C500-LK201-V1 , C500-LK203 231
- CV500, CV1000, CVM1 231
- (Switch) 231
- (DIP switch) 231
- (System setting) 231
- (PC system setting) 232
- PLC Link Communication Time 234
- 9-7 PLC Link Troubleshooting 235
- PLC Link Error 236
- Active No [ESC] 236
- 1 Specifications 238
- 2 Dimensions 239
- 3 Error Messages 240
- 4 ASCII Code Table 241
- 5 Setting Item List 242
- Appendix-7 243
- Appendix-8 244
- 6 Factory Setting List 245
- Appendix-10 246
- 7 PLC Program Examples 247
- KV Series 247
- Initialization of the DM 247
- Control of the read trigger 248
- Data read process 248
- Select active record 248
- MELSEC Series 249
- SYSMAC Series 251
- Appendix-17 253
- 8 Preset Mode Status Output 254
- Appendix-19 255
- 10 Test Barcodes 256
- 11 Index 257
- Appendix-22 258
- Appendix-23 259
- Appendix-24 260
- WARRANTIES AND DISCLAIMERS 261
Comments to this Manuals
Related products and manuals for Sensors Keyence DV-90
Sensors Keyence N-400 User Manual
(150 pages)
(150 pages)
Sensors Keyence N-410 User Manual
(160 pages)
(160 pages)
Sensors Keyence KV Series User Manual
(26 pages)
(26 pages)
Sensors Keyence KV Series User Manual
(6 pages)
(6 pages)
Sensors Keyence KV Series User Manual
(240 pages)
(240 pages)
Sensors Keyence KV-D20 User Manual
(72 pages)
(72 pages)
Sensors Keyence Visual KV Series User Manual
(444 pages)
(444 pages)
Sensors Keyence Visual KV Series User Manual
(392 pages)
(392 pages)
Sensors Keyence MS-F07 User Manual
(2 pages)
(2 pages)
Sensors Keyence MS2 Series User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
s