Keyence IG Series User Manual Page 89
- Page / 164
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
4-2 Basic Settings and Advanced Settings
4-31
IG-E
4
Setting Various Functions
Yo u can check the validity of a measurement by checking the number of edges in the
measuring range.
The examples of use are as follows.
• Preventing abnormal values from being measured due to dust, oil, etc. stuck to the
measurement part (Setting B).
• Detecting a foreign object incorporated (setting A or B)
• Confirming that the target is inserted into the measurement range (setting A)
Number of edges-setting screen
When the setting A or setting B is set, the display goes to the number of edges-setting
screen. (When OFF is set, this screen is skipped.)
Press
S
/
T
button on the number of edges-setting screen to specify the number of edges.
The number of edges being measured is displayed on the main display (upper level).
9. Edge check function
Edge check function Description
Default
value
Off
The edge check function is not used. c
Setting A
If the number of edges of the target differs from the
specified number, the check indicator [CHECK] lights up
and the edge check output (green wire) is turned ON.
"Power/Input-output cable" (page 2-7)
Setting B
If the number of edges of the target differs from the specified
number, the check indicator [CHECK] lights up and the edge
check output (green wire) is turned ON. However, if the
number of edges of the object is 0 (when the object cannot
be measured), the check indicator [CHECK] is turned off
and the edge check output is turned OFF.
"Power/Input-output cable" (page 2-7)
Reference
•Set B if you wish to distinguish between the case that the object is not
present within the measurement range and the case that the number of
edges of the object differs from the specified number.
• The above explanation is applicable to the case when the output mode of
judgment output is Normal Open (default value). Only ON/OFF of the edge
check output is reversed for Normal Close.
"4. Output mode" (page 4-19)
Item Setting range Default value
Number of edges 0 to 99 1
#
LASER
BANK
0
1
2
3
HI
LO
R.V.
ANALOG
HI SHIFT
ZERO SHIFT
TIMING
LO
ALIGNMENT
%J-
GO
HOLD CALC
CHECK
'&)
LASER
BANK
0
1
2
3
HI
GO
LO
R.V.
ANALOG
HI SHIFT
ZERO SHIFT
TIMING
LO
ALIGNMENT
%PV
HOLD CALC
CHECK
FGH.V
LASER
BANK
0
1
2
3
HI
LO
R.V.
ANALOG
HI SHIFT
ZERO SHIFT
TIMING
LO
ALIGNMENT
#P)
GO
HOLD CALC
CHECK
9. Edge check
Number of edges-setting screen
10. Analog output scaling
[MODE]
or X
[MODE]
or X
- IG Series 1
- Introduction 2
- General Precautions 3
- Abnormal Conditions 4
- Precautions on Use 4
- Other Precautions 5
- CE Marking 5
- Precautions on UL Certificate 5
- Table of Contents 6
- Chapter 5 Specifications 8
- Before Use1 11
- 1-1 Overview of the IG Series 12
- Light-shielding object 13
- Level to be measured 15
- Checking the Package Contents 16
- Sensor Head 17
- List of Optional Parts 18
- 1-3 Part Names and Functions 19
- Amplifier control unit 20
- 1-3 Part Names and Functions 21
- Sensor Head Unit 22
- Installation and Connection2 23
- Mounting the Sensor Amplifier 24
- Installation and Connection 26
- Expansion cable 27
- Main unit 27
- Expansion unit 1 27
- Power/Input-output cable 28
- To attach To remove 28
- Mounting the Sensor Head 30
- IG-010 IG-028 32
- Sensor Head Connection 34
- [T] connector of amplifier 35
- Insert further 36
- Basic Operations3 37
- 'PF 38
- [HOLD] ON 39
- Sub Display (Lower Level) 40
- Setting Operations 42
- 3-3 Optical Axis Alignment 44
- Initial Reset (Initialize) 46
- Manual Setting 48
- Item Setting range 49
- Default value 49
- Two-point tuning 50
- Shift target value 52
- How to Switch the Bank 55
- 3-9 Key Lock Function 57
- Selecting the Display Unit 58
- Setting Various Functions4 59
- 4-1 Setting Operations 60
- 4-1 Setting Operations 61
- List of Setting Items 62
- Setting Various Functions 63
- #W' 64
- 1. Measurement mode 66
- Edge control/Positioning mode 67
- Inner diameter 69
- Glass edge mode 70
- Pin position measurement mode 71
- 'F) 74
- 'F) 74
- 2. Measurement direction 75
- 4. Output mode 77
- Sample hold 79
- Peak hold 80
- Bottom hold 81
- Peak-to-peak hold 82
- *.& 83
- &.; 83
- 6. Timing input 85
- 7. Delay timer 85
- Timing chart 86
- &.;6 87
- 8. Hysteresis 88
- 9. Edge check function 89
- 10. Analog output scaling 90
- 11. External input 91
- Zero shift input 92
- Reset input 92
- Timing Input 93
- Minimum Input Time 94
- Bank A input/Bank B input 95
- Laser emission stop input 96
- Gain input 96
- 15. Display Digit 98
- 16. Power saving indication 99
- 17. Position monitor 99
- 18. Display Color 101
- Binarization Level 102
- Received light 103
- 5'P 104
- 4-4 Calculation Function 105
- Addition Mode 106
- Subtraction Mode 107
- 2 heads Mode 107
- *'#F 108
- Reference 109
- 4-5 Calibration Function 110
- 5'6 111
- 5'6 111
- Specifications5 113
- 5-1 Specifications 114
- Sensor Amplifier 115
- 5-2 Circuit Diagram 116
- Input Circuit Diagram 117
- 5-3 Dimensions 118
- , others 0.15 mm 119
- 2-M3 Valid screw depth 120
- * Light-receiving area 120
- (5 x 14 rectangle) 120
- (3.6 x 31.2 rectangle) 121
- Measurement range 122
- Software Licensing Conditions 124
- Trademarks 125
- 6-2 Before Use 126
- Preparation for installation 127
- Notes for Windows XP/2000 127
- Notes for Windows Vista 128
- Installation 128
- 6-2 Before Use 129
- Connecting with a Computer 133
- 6-3 Part Names and Functions 134
- Main panel 135
- Main panel switching tab 135
- Sub panel 135
- 6-4 Configuration Tab 136
- Sensitivity tab 138
- Advanced settings tab (Pro) 139
- 6-4 Configuration Tab 140
- 6-5 Monitor tab 142
- Waveform Display 143
- Monitor Tool Bar 143
- Data output 144
- Function Screen 145
- Key Lock Button 146
- 6-6 Menu Bar 147
- Communication 148
- Language 149
- 6-6 Menu Bar 150
- IG User’s Manual 150
- About IG Configrator 150
- Appendix 151
- 1 Troubleshooting 152
- 'T* 154
- Displays alternately 155
- 'TTF 156
- 'TTQ 157
- 'TT5 157
- 'TTP 157
- 'TT 158
- 2 Display Screen and Output 159
- 4 Index 161
- WARRANTIES AND DISCLAIMERS 163
Comments to this Manuals
Related products and manuals for Sensors Keyence IG Series
Sensors Keyence IB Series User Manual
(12 pages)
(12 pages)
Sensors Keyence IB Series User Manual
(3 pages)
(3 pages)
Sensors Keyence IB Series User Manual
(124 pages)
(124 pages)
Sensors Keyence DL-CL1 User Manual
(72 pages)
(72 pages)
Sensors Keyence DL-CL1 User Manual
(74 pages)
(74 pages)
Sensors Keyence IL Series User Manual
(3 pages)
(3 pages)
Sensors Keyence IL Series User Manual
(140 pages)
(140 pages)
Sensors Keyence GT2 Series User Manual
(3 pages)
(3 pages)
Sensors Keyence GT2-100 Series User Manual
(16 pages)
(16 pages)
Sensors Keyence GT2-500 Series User Manual
(16 pages)
(16 pages)
Sensors Keyence GT2-70 Series User Manual
(16 pages)
(16 pages)
Sensors Keyence GT2-H12xxF User Manual
(1 pages)
(1 pages)
Sensors Keyence GT Series User Manual
(3 pages)
(3 pages)
Sensors Keyence GT-70A Series User Manual
(10 pages)
(10 pages)
Sensors Keyence GT-A22L User Manual
(2 pages)
(2 pages)
Sensors Keyence LK-CC100/DN100 User Manual
(72 pages)
(72 pages)
Sensors Keyence LK-G5000 Series User Manual
(24 pages)
(24 pages)
Sensors Keyence LK-H2 User Manual
(76 pages)
(76 pages)
Sensors Keyence LK-HA100 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.107 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
No comment