Keyence N-400 User Manual Page 79
- Page / 150
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
71
Chapter 4 Multi-Drop Link Mode Control Procedure
4
● Checking individual ID number
Command: IDCHKmm
[mm = 01 to 31 (ID number)]
Response:
ON: Registered
OFF: Not registered
ERR01: “mm” exceeds the range of “01” to “31”.
● Registering serial ID numbers
Command: IDMAXmm
[mm = 01 to 31 (ID number)]
Response: OK
ERR01: “mm” exceeds the range of “01” to “31”.
Description: Registers all ID numbers not more than “mm”.
When “mm” is “00”, registering serial numbers is disabled.
● Checking serial ID numbers
Command: IDMAX
Response: MAXmm
mm = 01 to 31 (ID number)
mm = 00 : Not registered
mm = 99: The registered ID numbers are not serial numbers.
Description:
Registers all ID numbers not more than “mm”.
When the registered ID numbers are not serial numbers, the response is “99”.
Saving registered ID numbers
The registered ID numbers for auto polling are saved in the N-400.
Command: IDSAVE
Response: OK
Controlling auto polling
Setting auto polling mode to ON or OFF.
● Auto polling ON
Command: POLE00
Response: OK
Example: Sending the command to start auto polling (When ten BL series units are
connected)
1. Send “ID001111111111000000000000000000000 [CR]” (or “IDMAX10 [CR]”).
2. The N-400 sends back “OK [CR]”.
3. Send “POLE00 [CR].”
4. The N-400 sends back “OK [CR]”.
- User's Manual 1
- Software License Agreement 2
- Safety Precautions 3
- List of Package Contents 4
- Contents 5
- Chapter 6 PLC Link 7
- WARRANTIES 7
- Chapter 1 9
- 1.1 Functions of the N-400 10
- 1.2 System Configuration 12
- 1.3 Part Names 13
- POWER SD RD 14
- Chapter 2 17
- 2.1 Installing the N-400 18
- Connecting power supply 20
- Internal circuit 21
- Pin assignment 24
- Connecting power supply 25
- 2.3.3 Connecting RS-485 27
- Incorrect 28
- 2.4.1 Connecting power supply 29
- 2.4.2 Connecting BL series 29
- Connecting trigger input 31
- 2.4.5 Connecting RS-485 33
- Example 1 34
- Example 2 34
- See pp. 19, 20 and 25 34
- 2.6 Mounting Procedure 35
- 2.6.2 Mounting N-400 36
- 2.6.3 Mounting N-48 36
- 2.6.4 Mounting BL-U1 37
- Chapter 3 39
- 3.1 Installing Setup Software 40
- 3.2.1 Operating procedure 42
- Mouse pointer 44
- • • • 44
- Entering a value 45
- Entering characters 45
- 3.3.1 Setting procedure 46
- Header, Delimiter: p. 61 48
- Checksum: pp.133 and 134 48
- PLC link: p. 100 49
- PLC trigger area: p. 106 49
- DM head address: p. 106 49
- File register: p. 101 49
- Matched Not matched 54
- 3.5 Using Monitor 60
- 3.6 List of Error Messages 63
- Chapter 4 65
- 4.1 Multi-Drop Link Mode 66
- 4.1.2 Setup procedure 68
- 4.2.1 Auto polling 69
- Header % P 05 Terminator 70
- Read data 73
- ACK/NAK protocol 74
- RTS/CTS control 74
- Serial command 75
- Command Response 76
- Command CR Response CR 76
- 4.4.1 Communication procedure 77
- 4.4.2 Description of commands 78
- Saving registered ID numbers 79
- Controlling auto polling 79
- Controlling reading operation 80
- Clearing transmission buffer 81
- Checking trigger input status 81
- Shift to SETUP mode 81
- 4.5 N-400 Setup Command 83
- ■ Response error codes 84
- Description of setup commands 85
- ■ PROTOCOL SETUP 87
- ■ ID SETUP 89
- ■ RS-232C SETUP 89
- ■ RS-485 SETUP 90
- Command Command 92
- Chapter 5 95
- 5.1 Multi-head Mode 96
- 5.1.2 Setup procedure 97
- Setting the N-400 98
- Setting the host computer 98
- “Single” label reading mode 99
- “Multi 1” label reading mode 99
- “Multi 2” reading mode 100
- “Level” trigger signal 101
- “One-shot” trigger signal 101
- 5.3.1 Communication format 103
- 5.3.2 Handshaking protocol 103
- 5.3.3 Read error code 103
- See p. 72 104
- 5.6 Communication Time 106
- Chapter 6 109
- 6.1 PLC Link 110
- Chapter 6 PLC Link 111
- 6.2 Setup Procedure 112
- 6.2.2 Setting the N-400 113
- 6.2.3 Setting the PLC 114
- 6.3 Device Assignment 116
- See p. 40 118
- Real-time control 119
- Sequential processing 119
- See the ASCII code 120
- Reading trigger area 122
- 6.4 PLC Link Error 124
- 6.5 Communication Time 125
- Appendices 127
- Appendix A Specifications 128
- Appendix B Dimensions 130
- Appendix C Sample Programs 132
- Sample program for PLC link 134
- Program for the KV series 138
- Appendix D Troubleshooting 139
- Appendix F ASCII Code Table 142
- Calculation range 143
- HOST MODE 145
- PROTOCOL SETUP 145
- ID SETUP 146
- RS-232C SETUP 146
- RS-485 SETUP 146
- WARRANTIES AND DISCLAIMERS: 149
Related products and manuals for Sensors Keyence N-400
Sensors Keyence N-410 User Manual
(160 pages)
(160 pages)
Sensors Keyence KV Series User Manual
(26 pages)
(26 pages)
Sensors Keyence KV Series User Manual
(6 pages)
(6 pages)
Sensors Keyence KV Series User Manual
(240 pages)
(240 pages)
Sensors Keyence KV-D20 User Manual
(72 pages)
(72 pages)
Sensors Keyence Visual KV Series User Manual
(444 pages)
(444 pages)
Sensors Keyence Visual KV Series User Manual
(392 pages)
(392 pages)
Sensors Keyence MS-F07 User Manual
(2 pages)
(2 pages)
Sensors Keyence MS2 Series User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 3.189 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals