Keyence LS-3100/3100W Series User Manual Page 10
- Page / 104
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
4
1-6. Preparation for Operation
CHAPTER 1 Preparation for Measurement
• Do not mount the scanning head to the place where a certain level of
electrical noise is applied or transferred. Isolate the scanning head if
electrical noise may be occured. Otherwise, laser diode may deteriorate
or become damaged.
• Although the LS controller has been thoroughly inspected before ship-
ment, we kindly request that you check it upon purchase for any damage.
Contact the nearest KEYENCE distributor if your LS controller is damaged
in any way.
• Precision components are incorporated in the scanning head, therefore be
sure not to subject it to shocks.
• The scanning head has been precision set before shipment. Always keep
the casing closed to maintain the head's setting.
• The LS controller can operate normally at 0 to 45°C (32 to 113°F) [0 to
40°C (32 to 104°F) for LS-3036/3060] with no freezing and 35 to 85%RH
without condensation. Operation outside these ranges may result in
malfunction.
Do not connect or disconnect any cables while the power is ON. Otherwise,
the laser diode may deteriorate and/or may be damaged.
1. Connect the controller to the scanning head and the transmitter and
receiver using the supplied cables.
The LS-3101(W) can be used with LS-3032, 3033, 3036 and 3060.
CAUTION
Note
LS-3032, LS-3034, LS-3036
LS-3033, LS-3033 SO, LS-3060
CAUTION
ls3100_01_06.p65 08.10.1, 10:49 AM4
- LS-3100(W) Series 1
- Unpacking 3
- WARRANTIES AND DISCLAIMERS 3
- CONTENTS 4
- Chapter 8 Error Messages 78 6
- Appendices 83 6
- WARRANTIES AND DISCLAIMERS 97 6
- LASER SAFETY PRECAUTIONS 7
- 1-4 Safety Consideration 8
- 1-3. Label Location 8
- LS-3060LS-3060 9
- LS-3032, LS-3034, LS-3036 10
- LS-3033, LS-3033 SO, LS-3060 10
- Grounding the 11
- Serial No 12
- Connect the correct scanning 12
- CHAPTER 2 13
- TRIAL OPERATION 13
- CHAPTER 3 14
- QUICK SETUP PROCEDURES 14
- 3-1. Common Settings 15
- 3-2. Measurement Procedures 16
- Gap Measurement 1 17
- Gap Measurement 2 17
- MODE NOMAL 18
- MODE P–P 18
- SEG D I A 18
- S E G E DGE1 18
- Measuring Target 19
- Displacement within 19
- Measuring Edge 19
- Movement 19
- Measuring Outer Diam 20
- Front Panel 21
- LS-3100 Series 21
- Back Panel 22
- LS-3033T 23
- LS-3033R 23
- 4-2. Indicators and Displays 24
- 4-3. Panel Keys 25
- See P.39 26
- See P.20 26
- See P.43 26
- Averaging Methods 27
- Analog Voltage Range 28
- See P.32 29
- See P.63, 64 30
- See P.63 30
- See P.29 31
- DIGIT SUPPRESS 32
- BAUD RATE 33
- POSITION CHECK 34
- Definition of Segment 36
- Description 36
- SEG ( 3 , 3 ) 37
- Segment Selector 38
- See P.31 39
- See P.31 40
- Segment Check 41
- Output Channel 43
- See P.43 or OFFSET value 44
- Transmitter 44
- Receiver 44
- MODE, OFFSET, and LIMIT 45
- C MODE Key 46
- 35 2. 345 50
- 2 36 1. 234 50
- G PROG (Program) 51
- See P.62 52
- Analog Voltage Output 53
- Comparator Output 53
- Specifications 55
- Pin Assignment 55
- Remote Operation 56
- Measurement in "mm" 60
- SP SP 6 0 . 0 0 0 0 63
- -SP60 . 0000C 63
- SP SP 1 0 . 0 0 0 0 CR 65
- -SP10 . 0000CR 65
- 1st data 2nd data 66
- Pin assignment 68
- Input Signal 69
- Output Signal 69
- Control Input Terminals 70
- Control Output Terminals 70
- MOUNTING SCANNING HEAD 71
- OS TP IOI N CHECK 72
- LED 7 lights 73
- CHAPTER 6 74
- OPTIONAL INTERFACE BOARDS 74
- 6-1. BCD Output 74
- External Trigger Input 76
- (EXT TRIG IN) 76
- Setting Address 78
- Setting Talk Only Mode 78
- Setting Delimiter 78
- Values or Other Data 79
- Talk Only Mode 79
- Setting Functions and 79
- Outputting Measured 79
- Status Byte 80
- Example of Program 81
- GP-IB Interface I/O 82
- Measuring Conditions 82
- CHAPTER 8 84
- ERROR MESSAGES 84
- CHAPTER 8 Error Messages 85
- CHAPTER 9 86
- TROUBLESHOOTING GUIDE 86
- OPERATING PRINCIPLE 89
- CHARACTERISTICS 90
- Temperature 91
- Characteristics 91
- (Typical) 91
- SPECIFICATIONS 92
- Scanning Head 93
- Approx.34 94
- APPENDIX E 95
- QUICK REFERENCE TABLE 95
- KEY FLOWCHARTS 97
- APPENDIX F Key Flowcharts 98
- FNC (Function) 100
- APPENDIX F Key Flowcharts 101
- APPENDIX F Key Flowcharts 102
- SAFETY PRECAUTIONS 103
Related products and manuals for Sensors Keyence LS-3100/3100W Series
Sensors Keyence GP-M Series User Manual
(28 pages)
(28 pages)
Sensors Keyence GP-M Series User Manual
(1 pages)
(1 pages)
Sensors Keyence AP-C30KP User Manual
(5 pages)
(5 pages)
Sensors Keyence AP-C30WP User Manual
(5 pages)
(5 pages)
Sensors Keyence AP-V42A(P) User Manual
(5 pages)
(5 pages)
Sensors Keyence AP-V42AW(P) User Manual
(5 pages)
(5 pages)
Sensors Keyence AP-40P User Manual
(5 pages)
(5 pages)
Sensors Keyence AP-30 Series User Manual
(4 pages)
(4 pages)
Sensors Keyence SK-1000 Series User Manual
(24 pages)
(24 pages)
Sensors Keyence DL-CL1 User Manual
(78 pages)
(78 pages)
Sensors Keyence SK-H Series User Manual
(12 pages)
(12 pages)
Sensors Keyence IV Series User Manual
(10 pages)
(10 pages)
Sensors Keyence IV Series User Manual
(6 pages)
(6 pages)
Sensors Keyence IV Series User Manual
(5 pages)
(5 pages)
Sensors Keyence IV Series User Manual
(110 pages)
(110 pages)
Sensors Keyence IV-D10 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 2.416 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals