Keyence LS-3100/3100W Series User Manual Page 70
- Page / 104
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
64
CHAPTER 4 Functions and Controls
Control Input Terminals
Input specifications
+12V
1.8 kΩ
680 Ω
GND
Photocoupler
Control input terminals
Internal circuit
Example of connection
•Contact (relays or switches)
LS controller
Control input
terminals
GND
LS controller
•Solid-state (transistors) Open-collector output
Control input
terminals
GND
Program Selector Input
Terminals
The desired program No. 1 to 5 can be selected from external equipment
using these terminals.
When terminal 5 (6, 7, 8, or 9) is grounded with terminal 10 for an instant,
program No. 1 (2, 3, 4, or 5) is selected and retrieved.
* When two or more terminals are grounded at the same time, the program
with the smallest number will be selected.
• When terminal 3 is grounded with terminal 4, the displayed and output
values are retained.
• When terminal 3 is disconnected from terminal 4, normal measurement is
resumed.
• When the LS controller is set to the P-P, PEAK, or BOTTOM mode, the
previous measured value is reset by grounding terminal 3 with terminal 4
and then disconnecting these terminals.
Hold Synchronous Input
Terminals
Laser Emission Control Input
Terminals (LASER REMOTE)
When terminals 11 and 12 are connected, the laser emission indicator LED
on the front panel lights. And, laser is emitted approx. 5 seconds after the
connection is made. When terminal 11 is disconnected form terminal 12, the
laser emission indicator LED goes out, and the laser emission stops.
The LS controller is delivered with a jumper inserted between terminals 11
and 12.
Control Output Terminals
Output Specifications
Comparator Output
Terminals
Relay: SPST-NO contact, 250 VAC, 2 A (resistive load)
• HIGH OUT terminals: HI
Comparator output is sent through these terminals when the measured value
is above the upper tolerance limit.
• LOW OUT terminals: LO
Comparator output is sent through these terminals when the measured value
is below the lower tolerance limit.
• GO OUT terminals: GO
Comparator output is sent through these terminals when the measured value
is within the tolerance range.
Use a crimp contact for wiring as shown below. Be sure to use a cable with
at least 0.4-mm sheath.
Round-shape Fork-shape
Note
ls3100_49_64.p65 08.10.1, 10:56 AM64
- LS-3100(W) Series 1
- Unpacking 3
- WARRANTIES AND DISCLAIMERS 3
- CONTENTS 4
- Chapter 8 Error Messages 78 6
- Appendices 83 6
- WARRANTIES AND DISCLAIMERS 97 6
- LASER SAFETY PRECAUTIONS 7
- 1-4 Safety Consideration 8
- 1-3. Label Location 8
- LS-3060LS-3060 9
- LS-3032, LS-3034, LS-3036 10
- LS-3033, LS-3033 SO, LS-3060 10
- Grounding the 11
- Serial No 12
- Connect the correct scanning 12
- CHAPTER 2 13
- TRIAL OPERATION 13
- CHAPTER 3 14
- QUICK SETUP PROCEDURES 14
- 3-1. Common Settings 15
- 3-2. Measurement Procedures 16
- Gap Measurement 1 17
- Gap Measurement 2 17
- MODE NOMAL 18
- MODE P–P 18
- SEG D I A 18
- S E G E DGE1 18
- Measuring Target 19
- Displacement within 19
- Measuring Edge 19
- Movement 19
- Measuring Outer Diam 20
- Front Panel 21
- LS-3100 Series 21
- Back Panel 22
- LS-3033T 23
- LS-3033R 23
- 4-2. Indicators and Displays 24
- 4-3. Panel Keys 25
- See P.39 26
- See P.20 26
- See P.43 26
- Averaging Methods 27
- Analog Voltage Range 28
- See P.32 29
- See P.63, 64 30
- See P.63 30
- See P.29 31
- DIGIT SUPPRESS 32
- BAUD RATE 33
- POSITION CHECK 34
- Definition of Segment 36
- Description 36
- SEG ( 3 , 3 ) 37
- Segment Selector 38
- See P.31 39
- See P.31 40
- Segment Check 41
- Output Channel 43
- See P.43 or OFFSET value 44
- Transmitter 44
- Receiver 44
- MODE, OFFSET, and LIMIT 45
- C MODE Key 46
- 35 2. 345 50
- 2 36 1. 234 50
- G PROG (Program) 51
- See P.62 52
- Analog Voltage Output 53
- Comparator Output 53
- Specifications 55
- Pin Assignment 55
- Remote Operation 56
- Measurement in "mm" 60
- SP SP 6 0 . 0 0 0 0 63
- -SP60 . 0000C 63
- SP SP 1 0 . 0 0 0 0 CR 65
- -SP10 . 0000CR 65
- 1st data 2nd data 66
- Pin assignment 68
- Input Signal 69
- Output Signal 69
- Control Input Terminals 70
- Control Output Terminals 70
- MOUNTING SCANNING HEAD 71
- OS TP IOI N CHECK 72
- LED 7 lights 73
- CHAPTER 6 74
- OPTIONAL INTERFACE BOARDS 74
- 6-1. BCD Output 74
- External Trigger Input 76
- (EXT TRIG IN) 76
- Setting Address 78
- Setting Talk Only Mode 78
- Setting Delimiter 78
- Values or Other Data 79
- Talk Only Mode 79
- Setting Functions and 79
- Outputting Measured 79
- Status Byte 80
- Example of Program 81
- GP-IB Interface I/O 82
- Measuring Conditions 82
- CHAPTER 8 84
- ERROR MESSAGES 84
- CHAPTER 8 Error Messages 85
- CHAPTER 9 86
- TROUBLESHOOTING GUIDE 86
- OPERATING PRINCIPLE 89
- CHARACTERISTICS 90
- Temperature 91
- Characteristics 91
- (Typical) 91
- SPECIFICATIONS 92
- Scanning Head 93
- Approx.34 94
- APPENDIX E 95
- QUICK REFERENCE TABLE 95
- KEY FLOWCHARTS 97
- APPENDIX F Key Flowcharts 98
- FNC (Function) 100
- APPENDIX F Key Flowcharts 101
- APPENDIX F Key Flowcharts 102
- SAFETY PRECAUTIONS 103
Related products and manuals for Sensors Keyence LS-3100/3100W Series
Sensors Keyence GP-M Series User Manual
(28 pages)
(28 pages)
Sensors Keyence GP-M Series User Manual
(1 pages)
(1 pages)
Sensors Keyence AP-C30KP User Manual
(5 pages)
(5 pages)
Sensors Keyence AP-C30WP User Manual
(5 pages)
(5 pages)
Sensors Keyence AP-V42A(P) User Manual
(5 pages)
(5 pages)
Sensors Keyence AP-V42AW(P) User Manual
(5 pages)
(5 pages)
Sensors Keyence AP-40P User Manual
(5 pages)
(5 pages)
Sensors Keyence AP-30 Series User Manual
(4 pages)
(4 pages)
Sensors Keyence SK-1000 Series User Manual
(24 pages)
(24 pages)
Sensors Keyence DL-CL1 User Manual
(78 pages)
(78 pages)
Sensors Keyence SK-H Series User Manual
(12 pages)
(12 pages)
Sensors Keyence IV Series User Manual
(10 pages)
(10 pages)
Sensors Keyence IV Series User Manual
(6 pages)
(6 pages)
Sensors Keyence IV Series User Manual
(5 pages)
(5 pages)
Sensors Keyence IV Series User Manual
(110 pages)
(110 pages)
Sensors Keyence IV-D10 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.524 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals