Keyence LS-3100/3100W Series User Manual Page 78
- Page / 104
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
72
Setting Address
Use the 1st to 5th DIP switches from the right (4, 5, 6, 7 and 8 in the figure)
to set the address. Addresses "0" to "30" can be set. To set the address to
"11", set the DIP switches as shown below.
With the LS controller, the address has been factory-set to "0".
Setting Talk Only Mode
To set the LS controller to the talk only mode, set the 3rd DIP switch from
the left (3 in the figure) to ON (down).
With the LS controller, the talk only mode has been factory-set to OFF (up).
* When the LS controller is set to the talk only mode, outputs are sent only
through CH1.
Setting Delimiter
Interface Messages
The responses to commands sent from the controller (computer, etc.) are as
follows:
CHAPTER 6 Optional Interface Boards
Use the 1st and 2nd DIP switches from the left (1 and 2 in the figure) to
select the delimiter for data transmission.
• To set the delimiter to "LF":
Set the 1st and 2nd DIP switches respectively to OFF and ON (as shown
below).
• To set the delimiter to "CR":
Set the 1st and 2nd DIP switches respectively to ON and OFF (as shown
below).
• To set the delimiter to "CR + LF":
Set both the 1st and 2nd DIP switches to OFF (as shown below).
* With the LS controller, the delimiter has been factory-set to "CR + LF".
EOI (End of Identify) can be output from the controller simultaneously when
the delimiter is transmitted from the LS controller. Select the appropriate
command to select how EOI is output.
Thus, you can select whether EOI is output simultaneously when the
delimiter is transmitted. In addition, you can output EOI alone from the
controller without transmitting the delimiter from the LS controller.
Initializes the interface, selected
device or all devices on the line.
1356784
ON
2
1356784
ON
2
1356784
ON
2
1356784
ON
2
Reads measured values into the GP-
IB buffer.
Response
Command
IFC InterFace CLear
"SDC" Selcted Device CLear
"DCL" Device CLear
"GET" Group Execute
Trigger
ls3100_65_75.p65 08.10.1, 10:57 AM72
- LS-3100(W) Series 1
- Unpacking 3
- WARRANTIES AND DISCLAIMERS 3
- CONTENTS 4
- Chapter 8 Error Messages 78 6
- Appendices 83 6
- WARRANTIES AND DISCLAIMERS 97 6
- LASER SAFETY PRECAUTIONS 7
- 1-4 Safety Consideration 8
- 1-3. Label Location 8
- LS-3060LS-3060 9
- LS-3032, LS-3034, LS-3036 10
- LS-3033, LS-3033 SO, LS-3060 10
- Grounding the 11
- Serial No 12
- Connect the correct scanning 12
- CHAPTER 2 13
- TRIAL OPERATION 13
- CHAPTER 3 14
- QUICK SETUP PROCEDURES 14
- 3-1. Common Settings 15
- 3-2. Measurement Procedures 16
- Gap Measurement 1 17
- Gap Measurement 2 17
- MODE NOMAL 18
- MODE P–P 18
- SEG D I A 18
- S E G E DGE1 18
- Measuring Target 19
- Displacement within 19
- Measuring Edge 19
- Movement 19
- Measuring Outer Diam 20
- Front Panel 21
- LS-3100 Series 21
- Back Panel 22
- LS-3033T 23
- LS-3033R 23
- 4-2. Indicators and Displays 24
- 4-3. Panel Keys 25
- See P.39 26
- See P.20 26
- See P.43 26
- Averaging Methods 27
- Analog Voltage Range 28
- See P.32 29
- See P.63, 64 30
- See P.63 30
- See P.29 31
- DIGIT SUPPRESS 32
- BAUD RATE 33
- POSITION CHECK 34
- Definition of Segment 36
- Description 36
- SEG ( 3 , 3 ) 37
- Segment Selector 38
- See P.31 39
- See P.31 40
- Segment Check 41
- Output Channel 43
- See P.43 or OFFSET value 44
- Transmitter 44
- Receiver 44
- MODE, OFFSET, and LIMIT 45
- C MODE Key 46
- 35 2. 345 50
- 2 36 1. 234 50
- G PROG (Program) 51
- See P.62 52
- Analog Voltage Output 53
- Comparator Output 53
- Specifications 55
- Pin Assignment 55
- Remote Operation 56
- Measurement in "mm" 60
- SP SP 6 0 . 0 0 0 0 63
- -SP60 . 0000C 63
- SP SP 1 0 . 0 0 0 0 CR 65
- -SP10 . 0000CR 65
- 1st data 2nd data 66
- Pin assignment 68
- Input Signal 69
- Output Signal 69
- Control Input Terminals 70
- Control Output Terminals 70
- MOUNTING SCANNING HEAD 71
- OS TP IOI N CHECK 72
- LED 7 lights 73
- CHAPTER 6 74
- OPTIONAL INTERFACE BOARDS 74
- 6-1. BCD Output 74
- External Trigger Input 76
- (EXT TRIG IN) 76
- Setting Address 78
- Setting Talk Only Mode 78
- Setting Delimiter 78
- Values or Other Data 79
- Talk Only Mode 79
- Setting Functions and 79
- Outputting Measured 79
- Status Byte 80
- Example of Program 81
- GP-IB Interface I/O 82
- Measuring Conditions 82
- CHAPTER 8 84
- ERROR MESSAGES 84
- CHAPTER 8 Error Messages 85
- CHAPTER 9 86
- TROUBLESHOOTING GUIDE 86
- OPERATING PRINCIPLE 89
- CHARACTERISTICS 90
- Temperature 91
- Characteristics 91
- (Typical) 91
- SPECIFICATIONS 92
- Scanning Head 93
- Approx.34 94
- APPENDIX E 95
- QUICK REFERENCE TABLE 95
- KEY FLOWCHARTS 97
- APPENDIX F Key Flowcharts 98
- FNC (Function) 100
- APPENDIX F Key Flowcharts 101
- APPENDIX F Key Flowcharts 102
- SAFETY PRECAUTIONS 103
Related products and manuals for Sensors Keyence LS-3100/3100W Series
Sensors Keyence GP-M Series User Manual
(28 pages)
(28 pages)
Sensors Keyence GP-M Series User Manual
(1 pages)
(1 pages)
Sensors Keyence AP-C30KP User Manual
(5 pages)
(5 pages)
Sensors Keyence AP-C30WP User Manual
(5 pages)
(5 pages)
Sensors Keyence AP-V42A(P) User Manual
(5 pages)
(5 pages)
Sensors Keyence AP-V42AW(P) User Manual
(5 pages)
(5 pages)
Sensors Keyence AP-40P User Manual
(5 pages)
(5 pages)
Sensors Keyence AP-30 Series User Manual
(4 pages)
(4 pages)
Sensors Keyence SK-1000 Series User Manual
(24 pages)
(24 pages)
Sensors Keyence DL-CL1 User Manual
(78 pages)
(78 pages)
Sensors Keyence SK-H Series User Manual
(12 pages)
(12 pages)
Sensors Keyence IV Series User Manual
(10 pages)
(10 pages)
Sensors Keyence IV Series User Manual
(6 pages)
(6 pages)
Sensors Keyence IV Series User Manual
(5 pages)
(5 pages)
Sensors Keyence IV Series User Manual
(110 pages)
(110 pages)
Sensors Keyence IV-D10 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 1.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals