Keyence SL-V Series User Manual Page 32
- Page / 168
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
2-4 Interlock Function
2-8
Functions and Features
2
SL-V-M-NO2-E
This mode can be used for the machine that nobody can go into or approach the hazardous area with
only passing through the protection zone, or can be used if the safety-related part of a control system
other than the SL-V, such as safety relay unit, can ensure the safety with other means.
Manual reset mode: Interlock function works. The SL-V starts operation if the SL-V receives the reset
operation.
The OSSD keeps the OFF-state even if the object detected by the SL-V is removed from the detection
zone. (Interlock condition).
It is necessary to perform the reset operation when the SL-V detects no interruption in the detection
zone, in order that the machine starts operation. Because of reset operation, the OSSD goes to the ON-
state, and then interlock condition is terminated.
This section explains the settings for the combination of automatic start and automatic reset mode.
Configuration
Wiring method (Pink wire on the transmitter)
SL-V can be set as the combination of automatic start and automatic reset mode through the wiring in
the following manner. If this function is set through the SL-VH1S, it cannot be set through the wiring.
Software method (SL-VH1S)
Refer to the "SL-VH1S User’s Manual".
Wiring
• If the power is turned on with an open circuit on the pink wire (interlock mode selection input), the SL-V
goes into the I/O monitoring mode.
See "I/O Monitoring Function" (page 2-50).
• If the power is turned on with an open circuit on the yellow wire (reset input) and the type of cable is
incorrect, the SL-V goes to the lockout condition because of "interlock error".
See "Troubleshooting" (page A-2).
• When the interlock is configured through the SL-VH1S, the pink wire on the transmitter must be insu-
lated from the external (keep open-circuit) because it is not needed if it is not used for other functions.
Automatic start / Automatic reset mode
0V
+24V
0V
+24V
Transmitter
Main
circuit
Receiver
Main
circuit
Blue
Brown
Yellow (reset input)
Blue
Brown
Pink (interlock mode selection input)
0V
+24V
0V
+24V
Transmitter
Main
circuit
Receiver
Main
circuit
Blue
Brown
Yellow (reset input)
Blue
Brown
Pink (interlock mode selection input)
When using a PNP output type cable When using an NPN output type cable
NOTE
- SL-V Series 1
- Introduction 2
- Safety Precautions 3
- Precaution on use 4
- Operators 4
- Environment of use 4
- Target machine 4
- Installation 5
- Circuit design and wiring 6
- Testing and maintenance 7
- Standards and regulations 8
- Table of Contents 9
- Chapter 4 Wiring 10
- Chapter 5 Optical Alignment 11
- Chapter 6 Indicators 11
- Appendix 12
- Before Use 13
- Checking the Package Contents 14
- 1-2 Options 15
- Hexagon socket bolt 15
- (M5, length: 6 mm, width 15
- (For mounting to the unit) 15
- Unit connection cable 16
- Junction cable 16
- Extension cable 16
- Cable combination example 17
- Series connection cable 18
- Cable length specification 18
- Protection bar 19
- SL-V Configurator (SL-VH1S) 20
- Upload configuration 21
- Download configuration 21
- Create/Save configuration 21
- Monitor light intensity 21
- 1-3 Part Description 22
- Part Description 23
- Functions and Features 25
- Cable Selection and Function 26
- Simple function type 27
- Multi-function type 27
- 2-2 Self-diagnosis Function 28
- Self-diagnosis Function 29
- 2-3 Series Connection 30
- 2-4 Interlock Function 31
- Configuration 32
- Interlock Function 33
- Interlock-reset-ready output 35
- Time chart 36
- 2-5 AUX (Auxiliary) Output 38
- 2-7 Wait Input Function 40
- 2-8 State Information Output 42
- State Information Output 46
- How to change the mode 48
- Making changes on the SL-V 48
- 2-9 Alert Output 49
- 2-10 Clear/Blocked Output 51
- SL-V-M-NO2-E 53
- Wiring for muting device 54
- Muting lamp wiring 54
- Limitations 54
- Muting bank function 56
- Reference 57
- Password setting 58
- Number 5 6 7 8 9 59
- Changing the password 60
- Steps (2) to (8) 62
- Steps (9) to (12) 62
- Steps (13) to (18) 62
- Steps (19) to (22) 62
- Entering the password 63
- Wiring 70
- 2-12 Fixed Blanking 72
- 2-13 Reduced Resolution 73
- OSSD is ON 73
- OSSD is OFFOSSD is ON 73
- 2-14 I/O Monitoring Function 74
- I/O Monitoring Function 75
- Correct Installation Method 78
- Safe Safe 79
- Dangerous 79
- 3-2 Safety Distances 80
- (2.76") or less 81
- Example 2 :ANSI B11.19-2010 82
- Detection 83
- S mm (inch) 83
- Series Connection 84
- 3-5 Cable Connections 87
- Cable Connections 88
- J (OP-83180) 91
- L-shaped mounting bracket 92
- Wiring the muting inputs 100
- Time chart 100
- Transmitter 100
- Workpiece 101
- Receiver 104
- Switch A2Switch A1 105
- Explanation 106
- Installation to a Machine 108
- SL-V-M-NO3-E 108
- SL-V-M-NO4-E 109
- Power supply 110
- 4-2 I/O Circuit Diagram 111
- Cable Color and Pin Position 112
- 4-4 Examples of Wiring 113
- 4-4 Examples of Wiring 114
- Optical Alignment 117
- 5-1 Optical Alignment 118
- Indicators 119
- Indication pattern 121
- During lockout condition 122
- 6-2 Function Indicators 123
- 6-3 Center Indicator 124
- Built-in indicator mode 125
- State indicator mode 125
- When setting on the SL-V unit 126
- Built-in indicator mode 127
- Center Indicator 128
- Specifications and Dimensions 129
- 7-1 Model 130
- 7-1 Model 131
- 7-2 Specifications 134
- Response time (OSSD) 135
- Current consumption 136
- 7-4 Dimensions (SL-VF/VH/VL) 137
- SL-VF Units: mm 138
- SL-VH Units: mm 138
- SL-VL Units: mm 139
- 7-4 Dimensions (SL-VF/VH/VL) 142
- Dimensions (SL-VF/VH/VL) 143
- Units: mm 143
- Back mounting Side mounting 143
- Protection bar 146
- ReceiverTransmitter 147
- Transmitter Receiver 147
- SL-VFM 148
- SL-VHM 148
- SL-VLM 151
- Dimensions (SL-VFM/VHM/VLM) 152
- A-1 Troubleshooting 154
- LED bar indicator 154
- Function indicator 154
- Troubleshooting 155
- A-2 Checklist 160
- Checklist 161
- Revision History 166
- E 1101-3 167
Related products and manuals for Lighting Keyence SL-V Series
Lighting Keyence SL-VH1S User Manual
(60 pages)
(60 pages)
Lighting Keyence SL-VHS Series User Manual
(10 pages)
(10 pages)
Lighting Keyence SL-C Series User Manual
(54 pages)
(54 pages)
Lighting Keyence SL-CHG Series User Manual
(54 pages)
(54 pages)
Lighting Keyence SL-CHS Series User Manual
(54 pages)
(54 pages)
Lighting Keyence SL-R11 User Manual
(42 pages)
(42 pages)
Lighting Keyence SL-R11E User Manual
(46 pages)
(46 pages)
Lighting Keyence SL-R12EX User Manual
(76 pages)
(76 pages)
Lighting Keyence SJ Series User Manual
(1 pages)
(1 pages)
Lighting Keyence SJ-H Series User Manual
(14 pages)
(14 pages)
Lighting Keyence SJ-HA Series User Manual
(12 pages)
(12 pages)
Lighting Keyence SJ-HS/HW/HM User Manual
(2 pages)
(2 pages)
Lighting Keyence SJ-F036 User Manual
(10 pages)
(10 pages)
Lighting Keyence SJ-F300 Series User Manual
(14 pages)
(14 pages)
Lighting Keyence SJ-M400 User Manual
(14 pages)
(14 pages)
Lighting Keyence SJ-M200 User Manual
(16 pages)
(16 pages)
Lighting Keyence SJ-M201 User Manual
(16 pages)
(16 pages)
Lighting Keyence SJ-M300 User Manual
(14 pages)
(14 pages)
© 2020, manymanuals.com. All rights reserved. | 0.969 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals