Keyence SL-V Series User Manual Page 73
- Page / 168
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
2-49
Functions and Features
2
SL-V-M-NO2-E
2-13 Reduced Resolution
This function is only enabled through the SL-VH1S.
In case of normal operation, the OSSD goes to the OFF state when the SL-V detects interruption in the
detection zone.
When you enable this function and set the number of ignored beams, the OSSD keeps the ON state
when the number of beams blocked by the object is less than or equal to the set number of ignored
beams. The OSSD only changes to the OFF state when the object consecutively interrupts more beams
than the set number of ignored beams.
The reduced resolution can be enabled to any of beam axis, including the beam axis of SL-V in series
connection.
When the reduced resolution function is applied, the detection capability varies depending on
your configuration. The following is the calculating formula.
[Detection capability under the reduced resolution function]=[Original detection
capability]+[Beam axis spacing]*[Number of ignored beams]
Therefore, make sure to accurately calculate the safety distance according to the detection
capability, and install the SL-V at a distance greater than or equal to the minimum safety
distance away from the hazardous zone or hazard. The installation of additional safety
measures, such as a safeguarding, may be required if the detection capability varies due to
the configuration of the reduced resolution function. On your own responsibility, you must
perform the risk assessment based on your configuration of the reduced resolution function in
order to reduce the risk.
Example: The number of ignored beams is set to "1"
The OSSD goes to OFF-state when the consecutive two beam axes are interrupted.
• Settable range for the number of ignored beams: one beam axis to the half of all beam axes (round down the
number of decimals)
• If the SL-V is connected in series, the all beam axes means sum of the beam axes of SL-V main unit and sub
units.
Procedure for Configuration
Refer to the "SL-VH1S User’s Manual".
Danger
: Obstacle : Obstacle : Obstacle
OSSD is ON
OSSD is OFFOSSD is ON
Reference
Cable
Self-diagnosis
Series Connection
Interlock
AUX
EDM
Wait
State Information
Alert
Clear/Blocked
Suspension
Fixed
Reduced
Monitoring
- SL-V Series 1
- Introduction 2
- Safety Precautions 3
- Precaution on use 4
- Operators 4
- Environment of use 4
- Target machine 4
- Installation 5
- Circuit design and wiring 6
- Testing and maintenance 7
- Standards and regulations 8
- Table of Contents 9
- Chapter 4 Wiring 10
- Chapter 5 Optical Alignment 11
- Chapter 6 Indicators 11
- Appendix 12
- Before Use 13
- Checking the Package Contents 14
- 1-2 Options 15
- Hexagon socket bolt 15
- (M5, length: 6 mm, width 15
- (For mounting to the unit) 15
- Unit connection cable 16
- Junction cable 16
- Extension cable 16
- Cable combination example 17
- Series connection cable 18
- Cable length specification 18
- Protection bar 19
- SL-V Configurator (SL-VH1S) 20
- Upload configuration 21
- Download configuration 21
- Create/Save configuration 21
- Monitor light intensity 21
- 1-3 Part Description 22
- Part Description 23
- Functions and Features 25
- Cable Selection and Function 26
- Simple function type 27
- Multi-function type 27
- 2-2 Self-diagnosis Function 28
- Self-diagnosis Function 29
- 2-3 Series Connection 30
- 2-4 Interlock Function 31
- Configuration 32
- Interlock Function 33
- Interlock-reset-ready output 35
- Time chart 36
- 2-5 AUX (Auxiliary) Output 38
- 2-7 Wait Input Function 40
- 2-8 State Information Output 42
- State Information Output 46
- How to change the mode 48
- Making changes on the SL-V 48
- 2-9 Alert Output 49
- 2-10 Clear/Blocked Output 51
- SL-V-M-NO2-E 53
- Wiring for muting device 54
- Muting lamp wiring 54
- Limitations 54
- Muting bank function 56
- Reference 57
- Password setting 58
- Number 5 6 7 8 9 59
- Changing the password 60
- Steps (2) to (8) 62
- Steps (9) to (12) 62
- Steps (13) to (18) 62
- Steps (19) to (22) 62
- Entering the password 63
- Wiring 70
- 2-12 Fixed Blanking 72
- 2-13 Reduced Resolution 73
- OSSD is ON 73
- OSSD is OFFOSSD is ON 73
- 2-14 I/O Monitoring Function 74
- I/O Monitoring Function 75
- Correct Installation Method 78
- Safe Safe 79
- Dangerous 79
- 3-2 Safety Distances 80
- (2.76") or less 81
- Example 2 :ANSI B11.19-2010 82
- Detection 83
- S mm (inch) 83
- Series Connection 84
- 3-5 Cable Connections 87
- Cable Connections 88
- J (OP-83180) 91
- L-shaped mounting bracket 92
- Wiring the muting inputs 100
- Time chart 100
- Transmitter 100
- Workpiece 101
- Receiver 104
- Switch A2Switch A1 105
- Explanation 106
- Installation to a Machine 108
- SL-V-M-NO3-E 108
- SL-V-M-NO4-E 109
- Power supply 110
- 4-2 I/O Circuit Diagram 111
- Cable Color and Pin Position 112
- 4-4 Examples of Wiring 113
- 4-4 Examples of Wiring 114
- Optical Alignment 117
- 5-1 Optical Alignment 118
- Indicators 119
- Indication pattern 121
- During lockout condition 122
- 6-2 Function Indicators 123
- 6-3 Center Indicator 124
- Built-in indicator mode 125
- State indicator mode 125
- When setting on the SL-V unit 126
- Built-in indicator mode 127
- Center Indicator 128
- Specifications and Dimensions 129
- 7-1 Model 130
- 7-1 Model 131
- 7-2 Specifications 134
- Response time (OSSD) 135
- Current consumption 136
- 7-4 Dimensions (SL-VF/VH/VL) 137
- SL-VF Units: mm 138
- SL-VH Units: mm 138
- SL-VL Units: mm 139
- 7-4 Dimensions (SL-VF/VH/VL) 142
- Dimensions (SL-VF/VH/VL) 143
- Units: mm 143
- Back mounting Side mounting 143
- Protection bar 146
- ReceiverTransmitter 147
- Transmitter Receiver 147
- SL-VFM 148
- SL-VHM 148
- SL-VLM 151
- Dimensions (SL-VFM/VHM/VLM) 152
- A-1 Troubleshooting 154
- LED bar indicator 154
- Function indicator 154
- Troubleshooting 155
- A-2 Checklist 160
- Checklist 161
- Revision History 166
- E 1101-3 167
Related products and manuals for Lighting Keyence SL-V Series
Lighting Keyence SL-VH1S User Manual
(60 pages)
(60 pages)
Lighting Keyence SL-VHS Series User Manual
(10 pages)
(10 pages)
Lighting Keyence SL-C Series User Manual
(54 pages)
(54 pages)
Lighting Keyence SL-CHG Series User Manual
(54 pages)
(54 pages)
Lighting Keyence SL-CHS Series User Manual
(54 pages)
(54 pages)
Lighting Keyence SL-R11 User Manual
(42 pages)
(42 pages)
Lighting Keyence SL-R11E User Manual
(46 pages)
(46 pages)
Lighting Keyence SL-R12EX User Manual
(76 pages)
(76 pages)
Lighting Keyence SJ Series User Manual
(1 pages)
(1 pages)
Lighting Keyence SJ-H Series User Manual
(14 pages)
(14 pages)
Lighting Keyence SJ-HA Series User Manual
(12 pages)
(12 pages)
Lighting Keyence SJ-HS/HW/HM User Manual
(2 pages)
(2 pages)
Lighting Keyence SJ-F036 User Manual
(10 pages)
(10 pages)
Lighting Keyence SJ-F300 Series User Manual
(14 pages)
(14 pages)
Lighting Keyence SJ-M400 User Manual
(14 pages)
(14 pages)
Lighting Keyence SJ-M200 User Manual
(16 pages)
(16 pages)
Lighting Keyence SJ-M201 User Manual
(16 pages)
(16 pages)
Lighting Keyence SJ-M300 User Manual
(14 pages)
(14 pages)
© 2020, manymanuals.com. All rights reserved. | 1.928 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals